The proposed rule would establish a safety standard for infant bouncer seats under section 104 of the Consumer Product Safety Improvement Act of 2008.

On 28 October, 2015 the U.S Consumer Product Safety Commission (CPSC) issued a Notice of Proposed Rulemaking (NPR) [1] to create a safety standard to cover infant bouncer seats ('bouncer seats') in response to the direction of section 104(b) of the CPSIA. This NPR also proposes to amend 16 CFR Part 1112 to add 16 CFR part 1229, should the standard become a final rule. The CPSC is inviting comments from the public and stakeholders, which should be submitted by 4 January, 2016.

The NPR is based on the most recent voluntary standard ASTM F2167-15 for Infant Bouncer Seats, with specific modifications to improve and strengthen the requirements for on-product warnings and instructional materials provided with bouncer seats.

The scope section of ASTM F2167-15 defines an 'infant bouncer seat' as: 'a freestanding product intended to support an occupant in a reclined position to facilitate bouncing by the occupant, with the aid of a caregiver or by other means.' ASTM F2167-15 states that infant bouncer seats are intended for 'infants who have not developed the ability to sit up unassisted (approximately 0 to 6 months of age).'

These infant bouncer designs use different methods to support the seat and are intended for 'bouncing,' as defined in ASTM F2167.

Incidents Reported:

Occurring between January 1, 2006 and February 2, 2015 total of 277 incidents including 11 fatalities and 51 injuries has been reported to CPSC involving bouncer seats. The hazard patterns related to incidents are listed below:

Hazard Pattern

Incident Reported

Product Design

Seventy-five (75)

Structural Integrity

Seventy (70)

Toy Bar-Related

Thirty-six (36)

Stability issues (tip-over)

Thirty-three (33)

Chemical/Electric Hazards

Thirty (30)

Restraints

Twenty (20)

Hazardous Placement

Eleven (11)

Unknown

Two (2)

Product Recalls

Since January 1, 2006, two bouncer seats were recalled involving two different firms. The first recall, in April 2007, involved 1,400units infant bouncer seats. The second recall in July of 2009, involved 6,500 units

ASTM F2167-15 sufficiently addresses most of the hazards associated with bouncer seats. However, to modify the effectiveness of warning label requirements, the Commission proposes to incorporate by reference ASTM F2167-15 with the following modifications:

  • Revise the content of the warnings, markings, and instructions to use the restraints '. . . even if baby is sleeping . . .'
  • Change the text in the warnings to read, 'stop using when baby starts trying to sit up'
  • Change the developmental guidance in the instructions, if stated, to read, 'from birth (or '0') until baby starts trying to sit up.'
  • Require that the fall hazard label be located on the front surface of the bouncer adjacent to the area where the child's head would rest, and modify the current visibility test to reflect this requirement.
  • Specify a standard format (including black text on a white background, table design, bullet points, and black border) for the warnings on the product and in the instructions.

SGS has dedicated experts and services to assist you in the development of juvenile products and childcare articles. We offer physical/mechanical tests, chemical tests, packaging evaluation, inspections to ensure the compliance of your products in target markets. The JPMA has selected SGS as the Principal Laboratory and Program Administrator due to its expertise and experience in quality, compliance and safety in the child care products industry around the world. Please do not hesitate to contact us for further information or visit our website.

For enquiries, please contact:

Ali Karimi
Director , Technical Services, Hardgoods Lab
t: +001 973-461-7928

© SGS Group Management SA - 2015- All rights reserved - SGS is a registered trademark of SGS Group Management SA. This is a publication of SGS, except for 3rd parties' contents submitted or licensed for use by SGS. SGS neither endorses nor disapproves said 3rd parties contents. This publication is intended to provide technical information and shall not be considered an exhaustive treatment of any subject treated. It is strictly educational and does not replace any legal requirements or applicable regulations. It is not intended to constitute consulting or professional advice. The information contained herein is provided 'as is' and SGS does not warrant that it will be error-free or will meet any particular criteria of performance or quality. Do not quote or refer any information herein without SGS's prior written consent.

distributed by