A wave of recent research projects presented at the latest International PEEK Meeting * in Washington, D.C., has highlighted the increasing adoption of PEEK implants in clinical practice as well as the material´s established position due to possible patient benefits. In particular, the potential of carbon fiber-reinforced PEEK (CFR-PEEK) plates for fracture fixation became increasingly compelling; moreover, additive manufacturing was revealed as making progress in the production of PEEK polymer-based implants.

Topics ranging from dental, knee, spinal and trauma implants up to advances in additive manufacturing or medical PEEK performance in general demonstrated the broad scope of current research in PEEK technology and clinical applications. More than 40 abstracts were shared through podium and poster presentations along with invited talks focusing on medical implantable PEEK to attendees from the FDA, industry, academia and research hospitals - supporting the growing relevance and necessity for the International PEEK Meeting.

Carbon fiber-reinforced PEEK (CFR-PEEK) composites - improving postoperative assessments
During the meeting potential of carbon fiber-reinforced PEEK (CFR-PEEK) composite plates for fracture fixation became clear and compelling, in particular for their high fatigue strength and a favourable modulus of elasticity. 'The potential benefits of a less stiff construct on healing are hugely attractive and the results from some early clinical comparative work with metals, which will be released in October, will only increase the interest in these materials ' said John Devine, Medical Business Director at Invibio Biomaterial Solutions, a leading pioneer and innovator of medical-grade PEEK such as PEEK-OPTIMA™.

One study assessed the mechanical stability of locking screws used in CFR-PEEK proximal humerus plates compared to those used in stainless steel plates. The results indicate that CFR-PEEK proximal humerus locking plates provide comparable or superior locking screw fixation strength compared to traditional stainless-steel locking plates. Plus, CFR-PEEK plates tolerated at least an equivalent, and in some sections of the plate, a significantly greater load before failure, when compared to traditional stainless-steel locking proximal humerus plates.

'A wealth of research and clinical experience is confirming that PEEK polymer-based implants have an established position due to potential patient benefits and, what is more, they still offer immense development possibilities,' commented Steve Kurtz, Ph.D., Implant Research Center, Drexel University (Philadelphia, PA, USA), and conference organizer. 'While additive manufacturing in medical is in its infancy, we think it could revolutionize the ease, speed and accuracy with which implants are manufactured.'

Future potential for additive manufacturing technology in medical
Additive manufacturing can deliver patient customized implants (PCI) and enables direct linkage to digital patient models that may change the face of pre-operative planning and surgery. 3D printing specialist Apium Additive Technologies GmbH, for example, is offering a commercially available 3D printer that is capable of processing PEEK. The model P 155 uses Apium´s innovative patent-pending Fused Filament Fabrication (FFF) 3D printing technology.

Researchers at Drexel University in Philadelphia have used the Apium machine to print intervertebral lumbar cages with experimental PEEK-filaments. Although both compressive and compressive-shear performance still need improvement, the researchers are working on that, as future additive technology has the potential to match the performance characteristics of machined cages.

PEEK polymer and the many virtues of radiolucency
Unlike metal implants, PEEK polymer implants offer all the advantages of radiolucency, enhancing the accuracy of implant procedures and enabling the timely diagnosis of post-operative complications.

Early clinical experience with a radiolucent CFR-PEEK pedicle screw system has demonstrated that the use of CFR-PEEK pedicle screws and rods reduces artifacts in computed tomography (CT) and especially magnetic resonance imaging (MRI). This facilitates better screw positioning and postoperative evaluation, and any potential loosening can be assessed in detail by MRI - additional CT investigation may no longer be necessary.

Further information is available on: https://invibio.com/international-peek-meeting (including a pdf with abstracts) and on www.medicalpeek.org

* This release references research reported at the International PEEK Meeting in Washington, D.C., from April 27-28, 2017. Invibio Biomaterial Solutions is proud to have been a sponsor of this event in alignment with the company´s mission to facilitate medical-device innovation by providing new solutions and support for PEEK-related research. For more than 15 years, Invibio has pioneered advances in the application of high-performance PEEK-based implantable polymers, such as the company's PEEK-OPTIMA and PEEK-OPTIMA HA Enhanced.


References 1) Is locking screw fixation in carbon fiber composite plates mechanically equivalent to stainless steel plates? Hak DJ. 2) Comparison of the Mechanical Properties of FFF 3D Printed and Machined Medical Grade PEEK Intervertebral Lumbar Cages. Başgül C, MacDonald DW, Siskey R, Kurtz SM. 3) Clinical Evaluation of a Radiolucent Carbon/PEEK Pedicle Screw System - Early Experience in Degenerative Cases with 12 months follow up. Nydegger T, Klabunde R, Rühli M.
About Invibio Biomaterial Solutions
Invibio, a Victrex plc company, is a global leader in providing high performance biomaterial solutions to medical device manufacturers. The company provides PEEK-OPTIMA™ polymers, advanced technical research and support and manufacturing of components for spine, trauma and orthopaedic medical segments for the development of long-term implantable medical devices. Today, Invibio's PEEK-OPTIMA™ polymers are used in ~9 million implanted devices worldwide. INVIBIO™, PEEK-OPTIMA™, INVIBIO BIOMATERIAL SOLUTIONS™ are trademarks of Victrex plc or its group companies. All rights reserved.

About Victrex plc

Victrex is an innovative world leader in high performance polymer solutions, focussed on the strategic markets of automotive, aerospace, energy, electronics and medical. Every day, millions of people use products and applications, which contain our materials - from smart phones, airplanes and cars to oil and gas operations and medical devices. With over 35 years' experience, we develop world leading solutions in PEEK and PAEK-based polymers, semi-finished and finished parts which shape future performance for our customers and our markets, and drive value for our shareholders. Find out more atwww.victrex.com

Copyright ©2017 Invibio Ltd.

Contacts

Invibio Biomaterial Solutions

Barbara Pasciak, Marketing Communications Manager

barbara.pasciak@invibio.com, Phone +1 484-342-6041

Victrex media contact

Beate Sauer, PR & Marketing Communications Manager

bsauer@victrex.com, Phone +49 61 92 / 96 49 19

Group media or Investor Relations enquiries

Andrew Hanson, Head of Investor Relations & Communications

ahanson@victrex.com, Phone +44 12538 98121

Victrex plc published this content on 29 August 2017 and is solely responsible for the information contained herein.
Distributed by Public, unedited and unaltered, on 29 August 2017 12:32:04 UTC.

Original documenthttps://www.victrex.com/en/news/2017/08/post-peek-meeting

Public permalinkhttp://www.publicnow.com/view/931E7848B8EDD7277D0C865C98807652270677F8