Talisker Resources Ltd. announced additional high-grade drill results highlighted by 56.88 g/t Au over 1.00 metre at its 100% owned Bralorne Gold Project. Key Points: Talisker initiated resource conversion drilling on October 17, 2023, with 15,000 metres of planned drilling and completed the program on February 15, 2024. Hole SB-2024-018 intersected 56.88 g/t Au over 1.00 metres on the BK-9870 Splay Vein.

Hole SB-2024-018 also intersected 11.74 g/t Au over 2.15 metres within a broader intercept of 3.31 g/t Au over 11.00 metres on the BK-9870 Vein. Hole SB-2024-007 intersected 8.81 g/t Au over 4.15 metres within a broader intercept of 3.34 g/t Au over 17.75 metres on the BK-9870 Vein. Hole SB-2024-007 also intersected 8.08 g/t Au over 2.20 metres on the Alhambra Vein.

The resource conversion drill program focused on increasing confidence in the Alhambra, BK and BK-9870 Veins. A total of 81 drill holes were drilled during the resource conversion program, totaling 14,949 metres. All assays have been received from Fourth Quarter 2023 and First Quarter 2024 drilling.

SB-2024-007 Hole Description: All assays have been received. Located in the King block and hosted in diorite intrusive. Intersected BK-9870 Vein from 55.35 ?

59.50 metres. Intersected Alhambra Vein from 133.80 ? 136.00 metres.

SB-2024-018 Hole Description: All assays have been received. Located in the King block and hosted in diorite intrusive. Intersected BK-9870 Splay Vein from 245.50 ?

246.50 metres. Intersected BK-9870 Vein from 283.15 ? 285.30 metres.

Major vein structures intersected are considered classic Bralorne crack-seal quartz-carbonate veins with densely banded sulphide septae. Crack-seal septae host fine-grained arsenopyrite and pyrite mineralization. Alteration halos consist of strong silica-sericite±mariposite alteration halos.

Drill core at the Bralorne Gold Project is drilled in HQ to NQ size ranges (63.5mm and 47.6mm, respectively). Drill core samples are a minimum of 50 cm and a maximum of 160 cm long along the core axis. Samples are focused on an interval of interest, such as a vein or zone of mineralization.

Shoulder samples bracket the interval of interest such that a total sampled core length of not less than 3m both above and below the interval of interest must be assigned. Sample QAQC measures of unmarked certified reference materials (CRMs), blanks, and duplicates are inserted into the sample sequence and makeup 9% of the samples submitted to the lab for holes reported in this release. ALS Global performs sample preparation and analyses in North Vancouver, British Columbia, Canada and SGS Canada in Burnaby, British Columbia, Canada.

Drill core sample preparation includes drying in an oven at a maximum temperature of 60°C, fine crushing of the sample to at least 70% passing less than 2 mm, sample splitting using a riffle splitter, and pulverizing a 250 g split to at least 85% passing 75 microns (ALS code PREP-31 /SGS code PRP89). Gold in diamond drill core is analyzed by fire assay and atomic absorption spectroscopy (AAS) of a 50g sample (ALS code Au-AA26 /SGS code GO_FAA50V10), while multi-element chemistry is analyzed by 4- Acid digestion of a 0.25 g sample split with detection by inductively coupled plasma mass spectrometer (ICP-MS) for 48 elements (Ag, Al, As, Ba, Be, Bi, Ca, Cd, Ce, Co, Cr, Cs, Cu, Fe, Ga, Ge, Hf, In, K, La, Li, Mg, Mn, Mo, Na, Nb, Ni, P, Pb, Rb, Re, S, Sb, Sc, Se, Sn, Sr, Ta, Te, Th, Ti, Tl, U, V, W, Y, Zn, Zr). Gold assay technique (ALS code Au-AA26 /SGS code FAA50V10) has an upper detection limit of 100 ppm.

Any sample that produces an over-limit gold value via the gold assay technique is sent for gravimetric finish (ALS method Au-GRA22 /SGS method GO_FAG50V) which has an upper detection limit of 1,000 ppm Au. Samples where visible gold was observed are sent directly to screen metallics analysis and all samples that fire assay above 1 ppm Au are re-analyzed with method (ALS code Au-SCR24 /SGS code - 6 - GO_FAS50M) which employs a 1kg pulp screened to 100 microns with assay of the entire oversize fraction and duplicate 50g assays on the undersize fraction. Where possible all samples initially sent to screen metallics processing will also be re-run through the fire assay with gravimetric finish provided there is enough material left for further processing.